MEAPS Configuration Commands I Table of Contents Table of Contents Chapter 1 MEAPS Configuration Commands.............................................................................................1 1.1 Global Commands............................................................................................................................1 1.1.1 mether-ring id1 domain id2..................................................................................................1 1.1.2 master-node...........................................................................................................................2 1.1.3 transit-node............................................................................................................................3 1.1.4 edge-node..............................................................................................................................4 1.1.5 assistant-node.......................................................................................................................5 1.1.6 major-ring...............................................................................................................................6 1.1.7 sub-ring...................................................................................................................................7 1.1.8 control-vlan............................................................................................................................ 8 1.1.9 single-subring-mode.............................................................................................................9 1.1.10 hello-time..............................................................................................................................9 1.1.11 fail-time...............................................................................................................................10 1.1.12 pre-forward-time................................................................................................................11 1.2 Port Configuration Commands.....................................................................................................12 1.2.1 mether-ring id1 domain id2 primary-port.........................................................................12 1.2.2 mether-ring id1 domain id2 secondary-port....................................................................13 1.2.3 mether-ring id1 domain id2 transit-port...........................................................................14 1.2.4 mether-ring id1 domain id2 common-port.......................................................................15 1.2.5 mether-ring id1 domain id2 edge-port.............................................................................16 1.3 Show.................................................................................................................................................17 1.3.1 show mether-ring................................................................................................................17 II MEAPS Configuration Commands Chapter 1 MEAPS Configuration Commands 1.1 Global Commands 1.1.1 mether-ring id1 domain id2 To set an instance of ring and enter the node mode, run the following command: mether-ring id1 domain id2 To cancel an instance of ring, run the following command: no mether-ring id1 domain id2 Parameters Parameters Description Id1 Stands for the node instance ID, which ranges from 0 to 7. Id2 Stands for the domain instance ID, which ranges from 0 to 3. Default Value By default, the ring node is not configured. Command Mode Global configuration mode Usage Guidelines If the configured domain is 0, that is id2 is o, domain id2can be omitted. Example S1_config#mether-ring 1 domain 2 S1_config_ring1# Related Command None 1 MEAPS Configuration Commands 1.1.2 master-node To configure an Ethernet ring as a master node, run the following command: master-node Parameters None Default Value By default, the node type is not configured. Command Mode Node configuration mode Usage Guidelines 1．A node can be set to be a master node, a transit node, an edge node or an assistant node. 2． After the node type, the node ring’s level and ring control VLAN are set, you need to decide whether to exist from the ring configuration mode and enable the ring's node, for if you conduct the two actions, the node type can never be modified. Example S1_config#mether-ring 1 domain 2 S1_config_ring1#master-node S1_config_ring1# Related Command transit-node edge-node assistant-node major-ring sub-ring control-vlan 2 MEAPS Configuration Commands 1.1.3 transit-node To configure the node type to be a transit node, run the following command. transit-node Parameters None Default Value By default, the node type is not configured. Command Mode Node configuration mode Usage Guidelines 1．A node can be set to be a master node, a transit node, an edge node or an assistant node. 2． After the node type, the node ring’s level and ring control VLAN are set, you need to decide whether to exist from the ring configuration mode and enable the ring's node, for if you conduct the two actions, the node type can never be modified. Example S1_config#mether-ring 1 domain 2 S1_config_ring1# transit-node S1_config_ring1# Related Command master-node edge-node assistant-node major-ring sub-ring control-vlan 3 MEAPS Configuration Commands 1.1.4 edge-node To set the node type to be an edge node, run the following command: edge-node Parameters None Default Value By default, the node type is not configured. Command Mode Node configuration mode Usage Guidelines 1．A node can be set to be a master node, a transit node, an edge node or an assistant node. 2． After the node type, the node ring’s level and ring control VLAN are set, you need to decide whether to exist from the ring configuration mode and enable the ring's node, for if you conduct the two actions, the node type can never be modified. Example S1_config#mether-ring 1 domain 2 S1_config_ring1# edge-node S1_config_ring1# Related Command master-node transit-node assistant-node major-ring sub-ring control-vlan 4 MEAPS Configuration Commands 1.1.5 assistant-node To set the node type to be an assistant edge node, run the following command: assistant-node Parameters None Default Value By default, the node type is not configured. Command Mode Node configuration mode Usage Guidelines 1．A node can be set to be a master node, a transit node, an edge node or an assistant node. 2． After the node type, the node ring’s level and ring control VLAN are set, you need to decide whether to exist from the ring configuration mode and enable the ring's node, for if you conduct the two actions, the node type can never be modified. Example S1_config#mether-ring 1 domain 2 S1_config_ring1# assistant-node S1_config_ring1# Related Command master-node transit-node edge-node major-ring sub-ring control-vlan 5 MEAPS Configuration Commands 1.1.6 major-ring To set the node ring’s level to be the major ring node, run the following command: major-ring Parameters None Default Value By default, the node ring’s level is not configured. Command Mode Node configuration mode Usage Guidelines 1． The node ring’s level can only be set to one of the two levels: major-ring or sub-ring. 2． After the node type, the ring’s level and ring control VLAN are set, you need to decide whether to exist from the ring configuration mode and enable the ring's node, for if you conduct the two actions, the node ring’s level can never be modified. 3． The edge node and the assistant node cannot be set to major ring. Example S1_config#mether-ring 1 domain 2 S1_config_ring1# transit-node S1_config_ring1#major-ring S1_config_ring1# Related Command master-node transit-node edge-node assistant-node sub-ring control-vlan 6 MEAPS Configuration Commands 1.1.7 sub-ring To set the node ring’s level to be the sub-ring node, run the following command: sub-ring Parameters None Default Value By default, the node type is not configured. Command Mode Node configuration mode Usage Guidelines 1． The node ring’s level can only be set to one of the two levels: major-ring or sub-ring. 2． After the node type, the ring’s level and ring control VLAN are set, you need to decide whether to exist from the ring configuration mode and enable the ring's node, for if you conduct the two actions, the node ring’s level can never be modified. 3． If the edge node or the assistant node is set, they are regarded as sub-rings by default. Of course, you can set them not to be sub-rings. Example S1_config#mether-ring 1 domain 2 S1_config_ring1#master-node S1_config_ring1#sub-ring S1_config_ring1# Related Command master-node transit-node edge-node assistant-node major-ring control-vlan 7 MEAPS Configuration Commands 1.1.8 control-vlan To set the control VLAN of the ring node, run the following command: control-vlan vlan-id Parameters Parameters Description vlan-id ID of the control VLAN Value range: 1-4094 Default Value By default, the control VLAN of a node is not configured. Command Mode Node configuration mode for the Ethernet ring Usage Guidelines 1． You can set any VLAN to be the control VLAN of a node and at the same time the system will create the corresponding system VLAN and another control VLAN according to the ring level. 2． After the node type, the ring’s level and ring control VLAN are set, you need to decide whether to exist from the ring configuration mode and enable the ring's node, for if you conduct the two actions, the ring control VLAN can never be modified. Example S1_config#mether-ring 1 domain 2 S1_config_ring1#master-node S1_config_ring1#sub-ring S1_config_ring1#control-vlan 2 S1_config_ring1# Related Command master-node transit-node edge-node assistant-node 8 MEAPS Configuration Commands major-ring sub-ring 1.1.9 single-subring-mode To configure the edge node or assistant edge node and enter the single subring mode, run the following command. single-subring-mode Parameters None Default Value Don't enter the single subring mode by default. Command Mode Node configuration mode for the Ethernet ring Usage Guidelines 1． Configuration of single-subring-node can only be effective in the edge node and the assistant edge node. 2． As in the single ring mode the subring protocol packet channel status detection on the main ring is not run, the dual-homing networking can't appear in the Ethernet ring. Example S1_config#mether-ring 1 domain 2 S1_config_ring1#edge-node S1_config_ring1#control-vlan 2 S1_config_ring1#single-subring-mode Related Command None 1.1.10 hello-time To configure the cycle for the master node to transmit the HEALTH packets of the Ethernet ring, run the following command: 9 MEAPS Configuration Commands hello-time value To resume the default value of the cycle, run the following command: no hello-time Parameters Parameters Description value Stands for a time value, whose unit is second. The default value is one second. The value ranges between 3 and 10 seconds. Default Value By default, the hello-time is three seconds. Command Mode Node configuration mode for the Ethernet ring Usage Guidelines 1． The hello-time configuration validates only on the master node. 2． By default, the value of the hello-time is smaller than that of the fail-time, which avoids the Ethernet ring protocol from being shocked. The hello-time needs to modify after modifying fail-time. Example S1_config#mether-ring 1 domain 2 S1_config_ring1#master-node S1_config_ring1#sub-ring S1_config_ring1#control-vlan 2 S1_config_ring1#hello-time 4 Related Command fail-time 1.1.11 fail-time To configure the time cap of waiting for the HEALTH packets for the secondary port of the master node, run the following command: fail-time value 10 MEAPS Configuration Commands To resume the default value of the fail-time, run the following command: no fail-time Parameters Parameters Description value Stands for a time value, whose unit is second. The default value is three seconds. The value ranges between 9 and 30 seconds. Default Value By default, the fail-time is 9 seconds. Command Mode Node configuration mode for the Ethernet ring Usage Guidelines 1． The fail-time configuration validates only on the master node. 2． By default, the value of the fail-time is triple of the hello-time, which avoids the Ethernet ring protocol from being shocked. The hello-time needs to modify after modifying fail-time. Example S1_config#mether-ring 1 domain 2 S1_config_ring1#master-node S1_config_ring1#sub-ring S1_config_ring1#control-vlan 2 S1_config_ring1#hello-time 4 S1_config_ring1#fail-time 12 Related Command hello-time 1.1.12 pre-forward-time To configure the time of maintaining the pre-forward state on the transit port, run the following command. pre-forward-time value 11 MEAPS Configuration Commands To resume the default value of the pre-forward-time, run this command. no pre-forward-time Parameters Parameters Description value Stands for a time value, whose unit is second. The default value is three seconds. The value ranges between 9 and 30 seconds. Default Value By default, the pre-forward-time is 9 seconds. Command Mode Node configuration mode for the Ethernet ring Usage Guidelines 1． The pre-forward-time configuration validates only on the transit node. 2． By default, the pre-forward-time on the transit node is triple the value of the hello-time on the master node, which avoids the network loop from being occurred after the transmission link recovers from disconnection. After the hello-time of the master node is modified, the corresponding pre-forward-time on the transit node need be adjusted. Example S1_config#mether-ring 1 domain 2 S1_config_ring1#transit-node S1_config_ring1#sub-ring S1_config_ring1#control-vlan 2 S1_config_ring1#pre-forward-time 12 Related Command None 1.2 Port Configuration Commands 1.2.1 mether-ring id1 domain id2 primary-port To set a port to be the primary port of a master node, run the following command: 12 MEAPS Configuration Commands mether-ring id1 domain id2 primary-port To cancel the primary port configuration of a port, run the following command: no mether-ring id1 domain id2 primary-port Parameters Parameters Description Id1 ID of the node Id2 ID of the domain Default Value The primary port is not configured by default. Command Mode The physical port configuration mode and the converged port configuration mode Usage Guidelines The primary port can be configured only when the ring control VLAN, the ring’s node type and the ring level are configured, and when the node type is the master node. If the configured domain is 0, that isid2 is o, domain id2can be omitted. Example S1_config#interface GigaEthernet 0/1 S1_config_g0/1# mether-ring 1 domain 2 primary-port S1_config_g0/1#exit Related Command master-node mether-ring id1 domain id2 secondary-port 1.2.2 mether-ring id1 domain id2 secondary-port To set a port to be the secondary port of a master node, run the following command: mether-ring id1 domain id2 secondary-port To cancel the secondary port configuration, run the following command: no mether-ring id1 domain id2 secondary-port 13 MEAPS Configuration Commands Parameters Parameters Description Id1 ID of the node Id2 ID of the domain Default Value The secondary port on the master node is not configured by default. Command Mode The physical port configuration mode and the converged port configuration mode Usage Guidelines The primary port can be configured only when the ring control VLAN, the ring’s node type and the ring level are configured, and when the node type is the master node. If the configured domain is 0, that isid2 is o, domain id2can be omitted. Example S1_config#interface GigaEthernet 0/3 S1_config_g0/3# mether-ring 1 domain 2 secondary-port S1_config_g0/3#exit Related Command master-node mether-ring id1 domain id2 primary-port 1.2.3 mether-ring id1 domain id2 transit-port To set a port to be the transit port of a transit node, run the following command: mether-ring id1 domain id2 transit-port To cancel the transit port, run the following command: no mether-ring id1 domain id2 transit-port Parameters Parameters Description Id1 ID of the node 14 MEAPS Configuration Commands Id2 ID of the domain Default Value The transit port on the transit node is not configured by default. Command Mode The physical port configuration mode and the converged port configuration mode Usage Guidelines The primary port can be configured only when the ring control VLAN, the ring’s node type and the ring level are configured, and when the node type is the transit node. Two transit ports can be configured on one transit node. If the configured domain is 0, that isid2 is o, domain id2can be omitted. Example S1_config_ring1#exit S1_config#interface GigaEthernet 0/1 S1_config_g0/1# mether-ring 1 domain 2 transit-port S1_config_g0/1#exit S1_config#interface GigaEthernet 0/3 S1_config_g0/3# mether-ring 1 domain 2 transit-port S1_config_g0/3#exit Related Command transit-node 1.2.4 mether-ring id1 domain id2 common-port To set a port to be a public port of an edge node (assistant edge node), run the following command: mether-ring id1 domain id2 common-port To cancel the public port, run the following command: no mether-ring id1 domain id2 common-port Parameters Parameters Description Id1 ID of the node 15 MEAPS Configuration Commands Id2 ID of the domain Default Value By default, there is no configuration of the public port of an edge node. Command Mode The physical port configuration mode and the converged port configuration mode Usage Guidelines The public port can be configured only when the ring control VLAN, the ring’s node type and the ring level are configured, and when the node type is the edge node. If the configured domain is 0, that isid2 is o, domain id2can be omitted. Example S1_config_ring1#exit S1_config#interface GigaEthernet 0/1 S1_config_g0/1# mether-ring 2 domain 2 common-port S1_config_g0/1#exit Related Command edge-node assistant-node mether-ring id1 domain id2 edge-port 1.2.5 mether-ring id1 domain id2 edge-port To set a port to be an edge port of an edge node (assistant edge node), run the following command: mether-ring id1 domain id2 edge-port To cancel the edge port configuration of a port, run the following command: no mether-ring id1 domain id2 edge-port Parameters Parameters Description Id1 ID of the node 16 MEAPS Configuration Commands Id2 ID of the domain Default Value By default, there is no configuration of the edge port of an edge node. Command Mode The physical port configuration mode and the converged port configuration mode Usage Guidelines The edge port can be configured only when the ring control VLAN, the ring’s node type and the ring level are configured, and when the node type is the edge node. If the configured domain is 0, that isid2 is o, domain id2can be omitted. Example S1_config_ring1#exit S1_config#interface GigaEthernet 0/3 S1_config_g0/3# mether-ring 2 domain 2 edge-port S1_config_g0/3#exit Related Command edge-node assistant-node mether-ring id1 domain id2 common-port 1.3 Show 1.3.1 show mether-ring To display the summary information about the Ethernet-ring node, run the following command: show mether-ring id1 domain id2 To display the detailed information about the Ethernet-ring node, run the following command: show mether-ring id1 domain id2 detail To display the information about the Ethernet-ring port, run the following command: 17 MEAPS Configuration Commands show mether-ring id1 domain id2 interface intf-name To display all summary information about the Ethernet-ring node, run the following command: show mether-ring Parameters Parameters Description Id1 ID of the node Id2 ID of the domain intf-name Name of an interface Default Value None Command Mode Monitoring mode, global configuration mode, node configuration mode or port configuration mode Usage Guidelines If the configured domain is 0, that isid2 is o, domain id2can be omitted. Example None Related Command None 18